Promo video for the AUT UAV team

This promotional video highlights our spatial ecologist - Dr Barbara Bollard Breen - and our partnership with Skycam UAV.  It demonstrates a launch sequence and flight with the Swampfox UAV developed by Skycam.  It was filmed as a part of a video to showcase the research we are doing at AUT through the Institute for Applied Ecology New Zealand.  Have a look at the website to see the full video http://www.aenz.aut.ac.nz/

A new expedition, a new face on the ice

This year, Professor Len Gillman, Head of School, has gone down to Antarctica, taking with him two modified Fox UAVs.  No doubt, Len will bring back lots of photographs and reports of the data collecting activities in the Taylor Valley.

The modifications to the Fox include battery upgrades for longer endurance and built-in redundancy in the control surface servos.  Failure of one elevon servo could cause the loss of the aircraft, or at least, deployment of the emergency parachute.  That would require a retrieve crew to find and recover the aircraft.  The last known position of the aircraft could be recovered from the GCS data log, but retrieval of the aircraft could involve a significant hike over the relatively difficult terrain.

Skycam UAV has split the elevons and fitted servos to each half, ensuring that a single failure would not cause the loss of the aircraft or an aborted mission.

A new multispectral camera has also been added to the sensor suite.  Similar to the vegetation stress camera, this unit can collect images in four bands, including infra-red.

In preparation for his deployment, Len spent some time with Skycam UAV personnel, working on the  systems and flying the Fox in D522, our regular test flying area in the Wairarapa.


Prof. Len Gillman and Dr. Tim Brooks during training in D522

First research paper published!

The AUT UAV team has just had its first research paper published in an international peer reviewed journal!

Application of an unmanned aerial vehicle in spatial mapping of terrestrial biology and human disturbance in the McMurdo Dry Valleys, East Antarctica.

 Barbara Bollard-Breen •  John D. Brooks •  Matthew R. L. Jones • John Robertson •  Sonja Betschart •  Olivier Kung •  S. Craig Cary • Charles K. Lee •  Stephen B. Pointing
Polar Biology DOI 10.1007/s00300-014-1586-7 Published on-line October 2014

Our thanks to Stephen for championing this paper

The paper describes our approach and provides analysis of the images collected in the January 2014 K020 expedition.   The mapping also clearly identified the footprint of campsites and walking trails on soils, and highlighted the potential of this technique in monitoring human impact in this fragile ecosystem.

The paper is also an example of the interdisciplinary and inter organisational nature of Antarctic research.

Advanced training

This week, Prof. John spent two days with Skycam UAV in Danger Area 522 doing some advanced training with the Fox UAV.

Drawing on its military origins, the Fox can act as an aerial relay station for communication between two ground control stations.  By the same token, the aircraft can be controlled from either GCS, while the non-controlling unit can monitor the flight.

On the first day, the Fox, now fitted with larger capacity batteries was launched and flown locally from our regular airfield on a farm in D522.  Text communication between two GCS units was tested and control was handed back and forth before the aircraft was landed.  When we took off, the Fox measured the wind speed at between 25 and 30 kph, but by the end of the flight, it was gusting 50kph.  The Fox was able to deal with this, but the conditions would not be suitable for collecting good images.  Lew Woods of Skycam decided to land the Fox in Partial Control mode - the operator has control over heading and throttle setting, while the autopilot assists by stabilising the aircraft.

On the second day, the conditions were much more gentle and Dr. Tim and Prof. John launched the Fox from our regular airfield  in D522, while the away team of Rene and Lew headed to Lew's farm on the edge of D522.  The Fox flew around the airfield conducting a photo survey before we commanded a new waypoint overhead Lew's farm.  The away team were informed that the Fox was en route and they monitored the progress of the flight on their own GCS.  As the Fox flew over the waypoint, we put our GCS into 'Listen' mode and the away team captured the aircraft and took control for the landing.

After a battery change, the Fox was relaunched, conducted a photo reconnaisance of Lew's farm and then sent back to our location.  The procedure was reversed and we took control of the Fox about 1000m out from the target, bringing the aircraft down for a conventional parachute recovery.

The exercise was a total success, with one or two lessons learned about the actual handover process and message relay.  A nice little surprise awaited us as we recovered the Fox and opened the hatch to turn the systems off.  Nestling inside the fuselage was a note with a message "Greetings from the A-team".  Perhaps a rather expensive way of delivering a smiley face, but a nice touch!


The Fox is watching Grass Grubs

The wonderful people at Skycam UAV who build and supply our UAVs have been surveying a local farm.

Grass Grubs are the larvae of the bronze beetle Eucolaspsis brunnea, and eat the roots of pasture grasses, causing significant damage and thus loss of productivity on New Zealand farms.  Since the damage can be seen by the naked eye, it was suggested that the Fox UAV could be used to assess the extent of infestation of the farm and thus help in planning eradication measures.

The Skycam team visited the farm and flew their Fox over the affected areas and collected a large number of photographs.  Coincidentally, Skycam UAV was approached by Simactive, a company providing photogrammetry software, offering to process a set of images as a demonstration of their product's capability.

Skycam sent a sub-set of the images (50) to Simactive, who processed them into an orthomosaic.  The result is shown below




Even to the untrained eye, it is obvious that the grass is severely damaged in this paddock and would provide little feed for sheep or cattle set to graze on it.

Since the images are georeferenced, the farmer can use the mosaic to plan treatment of the affected areas, though it is apparently difficult to treat established pasture 

(see http://www.pggwrightsonseeds.com/uploads/Forage%20Focus%20No%2014%20Grass%20Grub.pdf)

This is another example of the non-military use of UAVs and the way our research may benefit New Zealand.
Thanks to Skycam UAV for providing the images and to Simactive for producing the orthomosaic.


Successful Antarctic Expedition

We are now back at Scott Base, staging for our return to New Zealand tomorrow.

Our expedition to the Taylor Dry Valley was an outstanding success and over the next few weeks, I'll publish photographs and comments on the deployment of the Swampfox UAV, built and supplied by Skycam UAV in Palmerston North.  I want to thank the company specifically, because they supplied spare parts and advice for our operations.  Without their support, we would not have been able to complete our programme of research.

This has been an awesome experience and I hope that in future years, we will be able to conduct further flights in Antarctica.

Preparations

We have finished our Antarctic Field Skills course, capped last night by a camp out at Castle Rock, about 30 minutes' travel from Scott Base.  It is such a privilege to be here in this spectacular place.

We returned to Scott Base this morning and since then we have been preparing for our deployment on Thursday.  I have checked the UAVs and GCSs and run some simulations.  This was not 100% successful and has caused me some concern.  Fortunately, we have e-mail access to NZ from the base, so I was able to dicuss the problem with Dr. Tim Brooks of Skycam UAV.  We appear to have sorted it out.

Tomorrow I will weigh all the equipment cases to determine the total weight for the helicopter loading calculations.

I hope that the batteries, systems and cameras of the UAS will deal with the cold temperature. According to the manufacturers' data, we should be alright. Another concern is the possibility that the bungee rubber could become brittle in the cold.

Though not strictly a UAV subject, I have attached a picture of the stunning view from my tent this morning at 06.00  It was much the same last night at 23.30 though the sky was much clearer.  At 23.30 last night, the air temperature was 1C, but it was 17C in my tent, the result of the sun shining brightly.  This morning it was around -1C, but the wind made it seem quite a lot colder.

 
View from my tent 06.00

Equipment going South

A computer glitch has meant that Prof. John B. has been locked out of this blog for the last fortnight.  After many frustrating attempts, access has been restored.

This comes just in time: the Hawk and GCS have both been sent to the Antarctica New Zealand base in Christchurch for transport down to the ice.  Our new Fox UAV and a spare GCS have also been sent to Christchurch.

Skycam UAV have been very generous sponsors of our research, loaning us spare wings, repair items, replacement spars, batteries and motor, together with a complete GCS, so that should we have problems down there, we can continue to collect data.

Prof. John B will travel to the ice to take part in the K020 deployment as part of the New Zealand Terrestrial Antarctic Biodiversity Survey, using the UAVs to collect data on cyanobacterial mats in the Taylor dry valley.  This is a proof-of-concept project.  Using the vegetation stress camera and the two Sony NEX5-N cameras, the UAVs will survey the lake margins.  This is all new to John; he is a microbiologist, but has never worked on cyanobacteria, nor has he been to Antarctica before, so the 3 to 4 week deployment will be a steep learning curve.  This has been complicated by the unfortunate accident in which the AUT project leader broke his ankle, which ruled him out of travel to Antarctica this year.  However, if all goes well, the UAVs may be depolyed in future expeditions.

Since leaving Auckland, John has spent two days with Dr. Tim Brooks of Skycam UAV, training on the Fox.  The Fox is rather different from the Hawk, being a tailless aircraft, and is considerably easier to operate.  A different pre-flight checklist is used, but the GCS software is exactly the same, so type conversion is very straightforward.  As usual when John goes to the Manawatu, the weather conditions were not very conducive to UAV operation, but Tim and John achieved six training flights, collecting a large number of nIR and RGB images of part of the D522 area in Pahiatua.  The next flights will be down on the ice.  At least there are no trees there!

John hopes to keep colleagues and other interested UAV operators informed of the progress of the project via this website.

Acceptance flights of new UAV - Swampfox

Prof. John B went to Palmerston North last week to conduct acceptance flights of AUT's new Swampfox UAV.

The Fox is totally New Zealand designed and built - the airframe was designed by Skycam UAV Ltd. in conjunction with the University of Queensland, the autopilot was designed by the New Zealand Defence Technology Agency, and the whole aircraft and systems were constructed Skycam UAV.  The Fox is a flying wing configuration, rather than a conventional wings plus tailplane combination.

Dr. Tim Brooks with the Swampfox

As usual for this time of year, the Manawatu weather was unreliable and rain was forecast for the whole week.  However, carpe diem!  Monday dawned cloudy and a bit windy, but Prof. John B and Dr. Tim Brooks of Skycam packed the control vehicle and headed out to Mangahao in the Wairarapa to fly in Danger Area 522, which allows Beyond Visible Line of Sight (BVLS) flights up to 2500ft AMSL (approximately 2000ft AGL).

After assembly, which is very straightforward, Tim demonstrated the launch procedure.  The Fox can be operated from the same GCS as our Hawk, but the launch handling is a little different.  After pre take-off checks are complete, the Fox is attached to the bungee catapult and the Operator enters the Take-off command into the GCS computer.  In contrast to the Hawk, the motor does not immediately start, which is initially a bit disconcerting.  This is actually a good thing, because the Handler holds the Fox by the trailing edges, which places a very large propeller right between the wrists!  When the aircraft is released, the accelerometers in the autopilot sense the launch and the motor is turned on.  Rate of climb is around 700fpm.  Prof. John B did the second launch; the aircraft is 'bounced' on the catapult and released at the top of the bounce, so that the Fox is pointing about 15 degrees above horizontal. 

We had fitted two Sony NEX5-N cameras into the sensor cassette and during the two flights totalling about 50 minutes, we took around 3200 high resolution photographs, half in RGB, the other half in nIR.  These will be processed with Pix4UAV software and will be a little bonus for the farmer - we will provide the orthomosaics to the farmer.  It appears that the areas of grass grub infestation show up very well in these images.

Recovery of the UAV was straightforward - after the Return command was entered, the Fox returned to the launch point; Landing Mode 4 entered commanded the aircraft to descend to 150ft AGL and fly upwind before releasing the parachute.  The parachute allows the UAV to land upside down, thus protecting the sensor window and the winglets.

The remainder of the week was far too windy and wet for further flights, though we did go out again on Tuesday and did some ground testing of the video downlink on the Hawk.

The next time the Fox flies, it will probably be in Antarctica - the UAS is on its way to Christchurch now for transport to the ice.

Flight time - at last!



Taking advantage of a visit to the old homestead, Prof. John B. was able to spend two days training with Skycam UAV systems engineer, Dr. Tim Brooks.

Using our own unique ground control station, we prepared one of the Skycam test aircraft.  It's been a long time since our ground school, but working through the checklist, it all came back.

We were in D522, the Skycam UAV testing area, where we could fly up to 2500 feet and out of visual contact.  This danger area was the subject of a NOTAM; before the first flight and at intervals, we broadcast a warning to general aviation that Skycam was conducting unmanned aircraft operations.  As the aircraft headed off, following its pre-programmed flightpath, it was rather scary, but Tim wanted me to experience the feelings when the aircraft disappears from sight and you are totally dependent on the autopilot, telemetry and video downlink.

On the first day, we did two flights of around 50 minutes each.  The Hawk sensor bay was fitted with a GoPro.  This camera has a wide angle lens and can record about an hour of HD video. Our other sensors - Sony NEX5-N, Mintron 2-axis video and FLIR - will produce much flatter, less distorted images.

After launch, the Hawk circled the launch point at 850ft agl until commanded to fly to the quarry (see previous post).  The altitude was reset to 1100 ft and the Hawk flew to the quarry.  Then I followed a river to a new waypoint, using the computer to designate intermediate points.  After approximately 40 minutes, the Hawk was commanded to return to the launch point, where we reset altitude in decreasing steps, until we initiated the automatic landing mode (engine off, parachute deployed).  At this point, a thermal kicked off and the Hawk landed rather further away from the GCS than we would have liked.

After a battery change and new checklist, we flew for another 45 minutes.

The following day, the conditions were again ideal for flying and I was put through many of the procedures required to conduct flights and aerial data collection - handle launch, check footprint of stills camera, plan track to acquire a series of stills on a transect etc.  Finally, taking control of the Hawk in heading stabilised mode, I brought the aircraft down over the GCS, killed the throttle and deployed the parachute.  The Hawk landed 30 metres away from the GCS.

I have rather crudely edited a small composite video to show launch, flight and recovery phases.  The video is highly compressed to make it manageable for the Internet, but I think it shows clearly the potential of the Hawk for monitoring plants and animals.  The GoPro picked up quite a lot of motor and servo noise from the Hawk, but on the ground it is almost impossible to hear the aircraft as it flies overhead.

We also appear to have shown that the Earth is spherical and really quite small!

I have several times tried without success to upload the video clip mentioned above.  You can see it at:

http://www.youtube.com/watch?v=0mYxMRxa-i0 


Potential capabilities of our UAV

Skycam UAV, the makers of our Hawk, recently installed our Sony NEX5-N camera in their new SwampFox X5, a JV airframe design with the University of Queensland.  They flew the SwampFox in Danger Area 522 near Pahiatua, New Zealand.

Programming the SwampFox to run four transects and setting the camera to take overlapping images during the transects, a series of 124 photographs were captured.  "Swampy" can carry two cameras simultaneously, and the images were captured in RGB and infrared.

The images were sent to Dr Andrew Fletcher, Mined Land Rehabilitation research fellow, at the University of Queensland.  He processed them with Pix4D software and created a 3-dimensional image of the quarry - the area with the 'CV' lake.


The video gives an indication of the type of information that the Hawk can collect.  SwampFox was flown at an altitude of approximately 1100ft amsl.  Note that the original images were at 20cm resolution; the video is heavily compressed to make it maneagable for the Internet and appears to have been further compressed by Blogger.

You can see more videos and information on Skycam UAV's website:
www.kahunet.co.nz




Kahu Hawk training - final day

What a bust!  Our ground training is all done and each day we hoped to go out and fly, but the Manawatu weather defeated us.  We had learned from Day 3 that the wind in the UAV flying area could be deceiving.  John B, as a glider pilot, recognised the signs when he opened the curtains first thing - clouds moving quickly and trees showing significant movement.  So our final day involved more simulations of photographic runs and a discussion of how to deal with link loss and other emergencies.

We also had an opportunity to meet with Rene Redmond, Managing Director of Skycam UAV, to discuss deployment of our Hawk, details of aircraft under development and possible alternative sensor options for our machine.

Dr. Tim Brooks will be in Auckland next week and, weather permitting, we are hoping to arrange some flight training with the Hawk at the North Shore Model Aircraft Club.

We flew back to Auckland with our heads full of plans for the future and were relieved not to hear "Gyro clipped" when the aircraft rotated for takeoff!

Kahu Hawk Training - days two and three

On day two we arrived early, ready for action. Our first task was to assemble the ground control station, the aircraft and successfully complete the entire pre flight checks, and all of that on our own! We succeeded and then progressed to the more advanced modules of our training book. We learned how to plan a flight with waypoints using the built in maps and also in ArcGIS, we also learned how to program operations zones to restrict our areas of study. We then reviewed all of the voice commands and discovered the meaning of some of the more elaborate terms. By the end of the day we were slightly overwhelmed, so much to learn in such a short time!

Day three dawned bright and clear and we felt ready for take off! However, driving over to the UAV flying area, John B observed that maybe the wind was too strong and he suggested that we might not be flying, given that the car was being buffeted across the road and the trees were laying over! When we arrived on site, we measured the wind and it was blowing a steady 48 to 50 kph which was well above our maximum wind speed of 25kph. The airstrip was on top of a ridge and it was interesting to note that just behind the ridge there were patches of calm and varying wind directions, yet when you looked up at the clouds, the clouds were hurtling along. Clearly the conditions were not suitable for flying, so after a few moments of disappointment we made the most of the situation and practiced assembling and dismantling the system in windy outdoor conditions. Thanks goodness John B wore his wet weather gear, as the ground was very wet!  We took turns being the mission commander, shouting instructions (I quite enjoyed this role) and running through the preflight checklist, the ground station controller and the UAV handler. We even practiced using the bungy launch system, which was certainly not as easy as it looks when the experts do it. We all had a go, and by the end of the morning we certainly felt more confident!

We returned to SkyCAM after lunch and Lew gave us a demonstration on how to repair the airframe 
in the field and also back at the home base for more permanent repairs. These airframes are 
incredibly durable and robust, and relatively easy to repair (depending on the severity of the damage).

We are all looking forward to day four, and to getting up in the air!

The team assembling the ground control system (GCS)

Tim teaching John how to use the bungy launch system


John assembling the airframe


Kahu Hawk Training - day one

Day one at Palmerston North - Skycam training centre.

Today the team woke bright and early and headed out to Skycam where we were met by our trainer and Systems Integrator, Dr Tim Brooks. After a look around the warehouse and a quick glimpse at the new Kahu, Tim commenced the training with a safety induction and provided us with a thorough list of safety checks for flight planning (eg. Don't put your fingers into the whirly bit in the front). We then focussed on the structure of the airframe and learned how to assemble and disassemble the aircraft. We learned how the airframe was constructed and the navigation system and autopilot installed. We were taken through each step in the assembly of the system prior to flying.  Believe it or not, that took most of the day! It's a very complex system with some amazing feats of engineering.  We also learned how to assemble the base station and ran through several basic simulation flights. The most exciting part of the day was running through the check list, testing the autopilot, and testing the throttle and seeing our new video camera sending signal to the base station screen! We finished the day learning how to repackage our parachutes, some of us were better at it than others!